Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
This great article below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is extremely intriguing. Check it out yourself and decide what you think of it.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily available, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. Instead of employing a professional to take over a halfway-completed job, it is much better to think about using one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a new tub in your restroom if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your tools and material checklist need to consist of the following:
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and brand-new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can break rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt on Installing A Bathtub. Many thanks for finding the time to browse our piece of content. Liked our blog? Please share it. Help someone else locate it. We value reading our article about Installing A Bathtub.
Information Here
Report this page